★ Serving the Denver metro for 15 years All work by a licensed & insured Colorado contractor
info@denverstampedconcreteco.com
Denver Stamped Concrete LLC
Stamped Concrete

Is Stamped Concrete Slippery When It's Wet or Icy?

You love the way the patio looks. Then the sprinklers run, or the first wet snow melts off the roof, and you step out the back door and your foot slides. Or you're still deciding, and someone told you stamped concrete is slippery and that you'd be better off with a plain broom finish.

Both are fair things to be thinking about in November. One homeowner put it about as plainly as anyone could: fine when it's dry, but extremely slippery when wet, very close to ice skating rink slick. Someone else said they'd almost wiped out twice by their pool. Plenty of other people say theirs is only slippery if there's a puddle sitting on it. Both camps are telling the truth, and the difference between them usually comes down to what's sitting on top of the concrete.

Why some stamped concrete is slick and some isn't

Do you find the stamped concrete slippery when wet?

It can be, and when it is, the sealer is usually the reason rather than the stamping. A glossy film-forming sealer with nothing added for traction leaves a smooth layer that gets slick the moment it's wet, while the same slab with grit mixed into the sealer, or a penetrating sealer, has far more grip. On ice, every outdoor concrete finish is slick, so winter traction comes from drainage, shoveling and sand.

Stamped concrete gets sealed because the sealer is what makes the color come alive. The sealers that do that best are the film-forming kind, acrylics and urethanes, and they sit on the surface as a thin layer you can see. Without anything added, that layer is smoother than the bare concrete underneath it, and water on top of a smooth film is how people slip. One person who'd had a driveway done said the contractor sealed it without any anti slip agent, and that even with rain only they'd biffed it several times.

The texture of the pattern matters too. A smooth ashlar slate or a polished-looking finish has less to grip than a deeper stone or flagstone texture. One person comparing the two side by side said neither was sealed and the stamped was definitely more slippery than the brushed. A broom finish has thousands of small ridges going across it, and most stamp patterns are smoother than that across their faces.

There's also the stuff that builds up on top. Dust, pollen and a little grime collect in the low points of the pattern, and when water gets on that film it turns into something closer to grease. If your patio has gotten slicker over a couple of years, try a good scrub before anything else.

What makes it grip

The fix most of the time is grit in the sealer. A fine slip-resistant additive gets mixed into the last coat, so wet feet have something to catch on. Done right, it gives the surface the feel of very fine sandpaper. It also dulls the shine slightly, and one commenter in a concrete forum pointed out that enough grit to make a difference can look a bit like spilled salt up close, so it's a trade. On a walkway, a set of steps or around a pool that trade is worth making. On our stamped concrete work we add it to the sealer on pool decks, walkways and steps as a matter of course.

The grit needs to be the right size and mixed through the coat. One homeowner tried a powdered additive on their own and said it seemed too fine to do the trick, which matches what we'd expect when a very fine product goes into a thin coat. You should be able to feel the texture with a bare hand, and if you can't, it won't do much for a shoe.

The other lever is the sealer itself. Penetrating sealers soak into the concrete instead of sitting on top, so they add no slipperiness at all. The catch is that they won't give stamped work the wet look most people chose it for, so on a decorative patio a film-forming sealer with grit is usually the better answer. Our concrete sealing page goes through when we'd pick each one.

If you haven't poured yet, pattern choice is the third lever. A textured stone pattern and a slope that sheds water both help, and around water our pool deck page has more on finishes that give bare feet something to hold. If grip matters more to you than anything else, exposed aggregate and broom finishes are naturally slip-resistant, and there's no shame in going that way.

Ice is its own problem

One homeowner said that if you live where it snows, you already know ice on stamped concrete is the slickest thing in existence. Once there's ice on it, every outdoor concrete surface is slippery, stamped or plain, sealed or not, though a glossy film makes it worse. Grit in the sealer helps with a wet surface and a little with a light frost, but it does nothing once a sheet of ice has formed on top of it. A home inspector in one of the threads said they always warn people that stamped concrete or tile can be slippery in the cold wet weather, and that's the time to be most careful.

What keeps a stamped patio or walk safer in a Denver winter is mostly about water. A slab with enough slope sends meltwater off the surface before it can freeze there overnight, while a flat spot or a low corner holds a puddle that turns into ice by morning. We see around a hundred freeze-thaw cycles a year on the Front Range, so a puddle that sits there can freeze and thaw again almost every night through the winter. Watch where water stands after the next melt, and point downspouts so they don't empty across the path to the door.

Then shovel early, before foot traffic packs the snow into ice, and throw sand on it for traction. A deep pattern is harder to shovel clean than a flat finish, so a plastic-edged shovel and a second pass with a broom get more of it off without scraping the sealer. Sand works on any finish and won't hurt the concrete or the sealer. If your patio or walk is new this year, skip the deicer altogether this winter, for reasons we went through in should I put salt on my new concrete driveway this winter. On older concrete, go easy with it, since the magnesium chloride the roads use here is hard on both the sealer and the surface underneath.

What to do if yours is already slick

One homeowner summed this one up as a death trap in the middle of winter, and asked whether there was any way to make it anti slip now. There's a short-term answer for this winter, and a lasting fix that has to wait for spring.

Start by figuring out what you've got. Run your hand over a dry section. If the surface feels glassy and smooth, there's a film sealer on it with little or no grit. If it feels like fine sandpaper, the grit is there and something else is going on, and that usually means buildup, standing water or worn-off sealer.

For this winter, the moves are simple. Put down heavy rubber mats or stair treads at the doors and on any steps, keep the walking path shoveled to bare concrete, use sand, and scrub off the dust and pollen layer on a dry day above freezing. If one spot always holds water, that's where the ice will be, so keep an eye on it or set a planter there.

The permanent fix waits for spring. Sealer needs warm weather to go on and cure, roughly above fifty degrees, which is why the sealing season here closes in early fall, as we explained in my concrete looked fine in October and terrible in April. Stamped concrete here also needs resealing every two to three years because the sun at altitude breaks the sealer down faster than it would at sea level, so the next reseal is the natural time to add grit. If the old sealer is peeling or cloudy, it may need to come off first so the new coat bonds to the concrete instead of to a failing layer.

Deciding on stamped concrete if this worries you

Slipperiness is one of the common reasons people talk themselves out of stamped concrete. One person said they'd been told stamped concrete is slippery and harder to maintain, so they were going with a colored broom finish instead. That's a reasonable call, especially for a set of steps or a main walk that an older family member uses every day.

It's also fine to want the stamped look and still want grip. Ask the contractor three things before you sign: which sealer they'll use, whether grit goes into it and where, and how the slab will slope. Ask to see or feel a sample with the grit in it, because the right amount is something you can judge with your hand. You can mix finishes too, with a stamped patio and a broom-finish path or steps leading up to it.

If you want someone to take a look

If your stamped patio, walk or steps are slick and you're not sure why, take a photo of the area and one of a puddle after it rains, and call us at (720) 782-8086. We'll come out, look at the sealer, the texture and the slope, and tell you whether a scrub and grit at the next reseal will do it or whether the old coat needs to come off first, with a written, itemized price. If you're planning new stamped concrete, we'll talk through patterns, sealer and grit with you on site before anything gets poured.

Related

Answers

Frequently asked questions

Do you find the stamped concrete slippery when wet?

It can be, and when it is, the sealer is usually the reason rather than the stamping. A glossy film-forming sealer with nothing added for traction leaves a smooth layer that gets slick the moment it's wet, while the same slab with grit mixed into the sealer, or a penetrating sealer, has far more grip. On ice, every outdoor concrete finish is slick, so winter traction comes from drainage, shoveling and sand.

How do you make stamped concrete less slippery?

Mix a fine slip-resistant grit into the sealer so the surface feels like very fine sandpaper when it's dry. On a slab that's already sealed, the grit goes into the next coat, and if the old sealer is peeling or cloudy it may need to come off first. Sealer needs warm weather to cure, so in Denver that work waits for spring.

What should I put on icy stamped concrete?

Sand. It gives traction on any finish and won't hurt the concrete or the sealer. Shovel before foot traffic packs the snow into ice, skip deicer entirely on concrete poured this year, and go easy with it on older slabs, because magnesium chloride is hard on both the sealer and the surface.

Ready for concrete that lasts?

Get a free on-site quote this week. Honest pricing, no pressure, work backed by a warranty.